TOOLS YOU NEED TO SET UP A NEW BATHTUB

Tools You Need to Set Up a New Bathtub

Tools You Need to Set Up a New Bathtub

Blog Article

Book Your Appointment

On this page down the page you might get some excellent content involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a tub isn't exactly rocket science, however it does require strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a reasonably challenging project. If the old bathtub is easily accessible, the task can move speedily; if you need to open a wall surface to eliminate the old tub and also place the brand-new tub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will certainly need an assistant to vacate the old tub as well as set in the new one. See to it you have certified on your own for the job and also fit attempting it. Rather than working with a professional to take over a halfway-completed task, it is much better to consider using one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This write-up will assist you set up a new bathtub in your restroom if you have already gotten a brand-new bathtub as well as don't need to change the plan of your previous water pipelines.
Your tools and product checklist need to make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Preparing for the Setup


    To start with, the supporting framework provided with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make certain that if the faucet includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to stop strain on the tub.
    Fit the flexible tap ports to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you make use of every one of the provided washers.
    Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its final position.

    Removing Old Taps


    If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, switch on the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the limited accessibility that is often the case.
    Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
    Before proceeding to fit the new taps, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.

    Installing the Bath tub


    Making use of both wooden boards under its feet, place the bathtub in the required placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four little factors.
    The following objective is to make sure that the bath tub is leveled all round. This can be attained by inspecting the level as well as changing the feet on the bathtub until the level checks out level.
    To set up faucets, fit the bottom of the outermost flexible faucet adapter to the proper supply pipe by making a compression sign up with; after that do the exact same for the other tap.
    Activate the water as well as inspect all joints and also brand-new pipework for leakages as well as tighten them if needed. Load the bathtub and additionally inspect the overflow outlet and also the normal electrical outlet for leakages.
    Finally, deal with the bath paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub needs to wait until the tub has actually been used at the very least once as this will certainly settle it right into its last position.

    Suitable New Taps


    If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the existent supply pipes.
    If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
    Next off, place the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in place in between the tap as well as the sink. Secure the tap in position with the maker offered backnut. As soon as the tap is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous kind should be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Tub


    In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to split an inflexible seal, creating the water to penetrate the wall between the bath as well as the tiling, causing issues with moisture and also feasible leakages to the ceiling listed below.
    You can select from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill the bathtub with water before sealing, to allow for the activity experienced when the bathtub remains in usage. The sealant can break relatively early if you do not consider this movement before securing.
    Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant adhesive and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    As a reader on A Step-by-Step Guide to Installing a Bathtub, I figured sharing that excerpt was smart. Please take the time to promote this blog entry if you enjoyed reading it. Thanks a bunch for your time. Kindly come by our blog back soon.




    Get Quote


    Report this page